MoreBeer:
Sunday, March 18, 2007
Building your own Randall
If you want to build your own Randall then you may find this shopping list useful. I bought all the parts from Morebeer, except the 1/2" OD stainless pipe that I drilled 20 small 1.5mm holes in. I'm sure you'll find the parts elsewhere also.
Using the Enamel Animal

The Randall has now been tested and used twice. It worked surprisingly well on both occations. The first time with 50 grams Centennial and the Scottish Export 80/-. The second time with 40 grams Amarillo and 10 grams Sorachi Ace and the India Pale Ale. Thanks to Frode for bringing the Sorachi Ace, a Japanese hop with an intense citrus aroma.

There were no leaks and the dual-serving system was well balanced. I had expected a little more resistance in the filter housing and the hop bed, but there was nothing wrong with the flow.
50 grams seems to be just the right amount of hops to use in this filter housing. It seemed a bit too little at first, but the hops soon swelled and filled the entire volume. The pressure in the keg started the flow of beer as soon as the line was connected to the keg. The Randall got filled about half full before the flow stopped as the air could not escape. Pressing the release valve replaced the air with beer. Note that it makes sense to let the hops soak a little while first.
The resulting beer is pretty amazing. There is an extremely intense hop aroma and flavour. You really need to enjoy hops to appreciate it. I felt that the aroma and the flavour of the two were somewhat different. The Centennial appeared much more oily and pungent than the Amarillo and Sorachi Ace did. This may have something to do with the kind of beer it was served through. My impression is that it is better to serve beers that have a higher alcohol content and more bitterness as this will help balance the end result. Otherwise the result is way over the top with regards to hop aroma.

So, what other things can one put inside the Randall other than hops?
Wednesday, March 14, 2007
Brew #43: Extra Special Bitter
This beer is a fairly bold ESB, both in original gravity and hops. It also has quite a bit of specialty malts, much more than I've had in any of my earlier attempts. I used mash hops with this brew, and it is the first time I try this in a British beer. The few times I've done this, with good results, have all been with hoppy American beer styles.
Again, I'm trying to get rid of my stock of old, but still usable yeast. I have a couple of vials of liquid yeast that I just have to throw away, but with this brew I should be left with a pretty decent set of fresh yeast packs, especially if I manage to squeeze in a double brew on Sunday. I used both the 11 grams packs I had just to be on the safe side. Even though it was past its best before date I'm sure it is more than enough of vital yeast for a beer like this. I store all my yeast, both dry and liquid, in the kitchen fridge.
The incredibly useful Mr. Malty's Pitching Rate Calculator™ says that the yeast in this particular beer must have a viability of minimum 67% for the two packs to be optimal. Go check it out. I'm sure you'll soon realize that you're underpitching. I sure did when I first tried to calculate the amount of yeast to pitch in my own beers. Since then I've tried my best to improve my pitching rates. Also make sure that you read Jamil Zainasheff's (Mr. Malty) Proper Yeast Pitching Rates article. It's almost scary how much vital yeast you need. Anyway, it is very helpful and makes you realize that yeast is extremely important to the quality of your beers.
The batch was brewed 2007-03-14.
Style:
Extra Special Bitter
Type:
All grain, batch sparge
Colour:
30 EBC (Copper)
Bitterness:
40 IBU
Malts:
5200g Maris Otter pale malt
750g Ambermalt
400g Wheat malt
450g Crystal 60L
200g Crystal 40L
250g Melanoidin malt
Mash:
66C, 60 min
76C, 10 min (mashout)
73% efficiency
Hops:
50g First Gold pellets 7.3%, mash hops
50g Fuggles pellets 5.1%, 60 min
50g First Gold pellets 7.3%, 10 min
50g Fuggles pellets 5.1%, 1 min
Yeast:
Safale S-04, 2 packs, best before 2007-01
Boil:
90 min
OG: 1.066 FG: 1.016 (estimated)
Again, I'm trying to get rid of my stock of old, but still usable yeast. I have a couple of vials of liquid yeast that I just have to throw away, but with this brew I should be left with a pretty decent set of fresh yeast packs, especially if I manage to squeeze in a double brew on Sunday. I used both the 11 grams packs I had just to be on the safe side. Even though it was past its best before date I'm sure it is more than enough of vital yeast for a beer like this. I store all my yeast, both dry and liquid, in the kitchen fridge.
The incredibly useful Mr. Malty's Pitching Rate Calculator™ says that the yeast in this particular beer must have a viability of minimum 67% for the two packs to be optimal. Go check it out. I'm sure you'll soon realize that you're underpitching. I sure did when I first tried to calculate the amount of yeast to pitch in my own beers. Since then I've tried my best to improve my pitching rates. Also make sure that you read Jamil Zainasheff's (Mr. Malty) Proper Yeast Pitching Rates article. It's almost scary how much vital yeast you need. Anyway, it is very helpful and makes you realize that yeast is extremely important to the quality of your beers.
The batch was brewed 2007-03-14.
Style:
Extra Special Bitter
Type:
All grain, batch sparge
Colour:
30 EBC (Copper)
Bitterness:
40 IBU
Malts:
5200g Maris Otter pale malt
750g Ambermalt
400g Wheat malt
450g Crystal 60L
200g Crystal 40L
250g Melanoidin malt
Mash:
66C, 60 min
76C, 10 min (mashout)
73% efficiency
Hops:
50g First Gold pellets 7.3%, mash hops
50g Fuggles pellets 5.1%, 60 min
50g First Gold pellets 7.3%, 10 min
50g Fuggles pellets 5.1%, 1 min
Yeast:
Safale S-04, 2 packs, best before 2007-01
Boil:
90 min
OG: 1.066 FG: 1.016 (estimated)
Monday, March 12, 2007
You know you're a brewing nerd...
...if you can spot the two logical errors in the photo below:

The mistakes I've made won't necessarily prevent the device from working, but they are clearly incorrect. Can you find them? (Click on the photo to see more details.)
I'm taking the device for a trial run on Thursday evening btw...
Update: The two logical errors were: 1. The red release valve button on top of the filter housing is placed next to the IN-connection, so having the tap mounted on this side is wrong. 2. The gray ball-lock quick connect is to be used for the IN-connection on the cornelius keg, since I want beer to flow through it I should have used a black ball-lock quick connection instead.

The mistakes I've made won't necessarily prevent the device from working, but they are clearly incorrect. Can you find them? (Click on the photo to see more details.)
I'm taking the device for a trial run on Thursday evening btw...
Update: The two logical errors were: 1. The red release valve button on top of the filter housing is placed next to the IN-connection, so having the tap mounted on this side is wrong. 2. The gray ball-lock quick connect is to be used for the IN-connection on the cornelius keg, since I want beer to flow through it I should have used a black ball-lock quick connection instead.
Wednesday, March 07, 2007
Bring on the hops!

I'm proud to present my latest homemade brewing gadget, a Randall. Its full name is Randall The Enamel Animal, and is also known as an organoleptic hop transducer module. The contraption was first invented by the Dogfish Head Brewery. It has later been bought by many pubs serving their beers, all in the the U.S. unfortunately, but they are to my knowledge only used for special events.
I have never tried it myself, but it sure looks like I good idea. I love hops and what couldn't be better than having beer pushed through lots of delicious hops cones on the way to your glass? Yummy!
As far as I know there are no places in Europe where one can try it. So, what was there to do other than to make one myself?

The device is made from one filter canister housing with threaded barbed fittings on both sides. Inside the filter there is a stainless steel pipe with twenty small 1.5 mm drilled holes. I had to get hold of and adapt this one myself. It wasn't easy as getting hold of a 1/2" stainless steel pipe was harder than expected. I ended up buying a towel rack from IKEA(!) and sawing it into pieces with a hack saw. Drilling the holes wasn't easy either as stainless steel is a pretty hard material. I ended up using five titanium covered HSS drills.
I have installed a dual system with two picnic faucets, so that one can serve the beer from the keg directly or from the Randall. That way it will be easy to find out what effect the hops have made to the beer.

The plan is to serve the keg of India Pale Ale through it at this year's Norwegian Homebrewers Festival. So, if you'd like to try it yourself you now know where to be on March 17th.
Friday, February 23, 2007
Homebrew shops in Norway?
Well, unfortunately there aren't that many options. In fact, there is just one single place where you can get a decent selection of brewing ingredients like malts and hops in this country. Yes, you heard right, just a single shop that sells hops or malts(!).
There are a lot of amateur wine and beer extract shops, but none of these provide anything close to what a non-newbie beer brewer would need. You cannot do without hops, and even malts if you're an all-grain brewer.

Petit Agentur is the place to get your brewing fix. They are located in Bergen on the west coast, something like 500 km away from where I live.
I understand that it probably isn't easy to run a small scale shop like this in a country of only 4.6 million inhabitants. So, I appreciate that there is at least someone who is willing to provide a great service to homebrewers in Norway.
Since I live in Oslo this means that I have to get orders shipped to me via the Postal Service. This is inconvenient especially when ordering sacks of malt. The shipping cost is approximately the same as the cost of the malt itself. For other brewing ingredients and other smaller items this is [almost] perfect.
The alternative for most homebrewers is to do their shopping in Sweden, Denmark or even the US.
But, if you're a homebrewer stuck in Norway this is the place.
There are a lot of amateur wine and beer extract shops, but none of these provide anything close to what a non-newbie beer brewer would need. You cannot do without hops, and even malts if you're an all-grain brewer.

Petit Agentur is the place to get your brewing fix. They are located in Bergen on the west coast, something like 500 km away from where I live.
I understand that it probably isn't easy to run a small scale shop like this in a country of only 4.6 million inhabitants. So, I appreciate that there is at least someone who is willing to provide a great service to homebrewers in Norway.
Since I live in Oslo this means that I have to get orders shipped to me via the Postal Service. This is inconvenient especially when ordering sacks of malt. The shipping cost is approximately the same as the cost of the malt itself. For other brewing ingredients and other smaller items this is [almost] perfect.
The alternative for most homebrewers is to do their shopping in Sweden, Denmark or even the US.
But, if you're a homebrewer stuck in Norway this is the place.
Tuesday, February 13, 2007
Extracts -- good or bad?
Is the use of extracts in beer brewing a good thing?
It is actually quite common for commercial breweries to use hop extracts. Even Belgian Trappist breweries do it(!). And their beers are considered among the best in the world.
In my opinion it is not necessarily a detriment to good beer. Same thing with malt extract, from which you can actually make some damn good beer. But it won't give you the same flexibility as all-grain would.
The reason the big commercial breweries use them is because they strive for consistency -- and hop extract give them just that. It is very predictable. That said they do also put a lot of effort into making beer cost-efficiently. On a larger scale the little things have a big influence on cost. Note that the reason they aren't using malt extract is that it is much more expensive than all-grain, which lets them squeeze the last drop of malt sugars out themselves.
This shouldn't stop them from making good beer though, as there is no defense against making bad beer.
It is actually quite common for commercial breweries to use hop extracts. Even Belgian Trappist breweries do it(!). And their beers are considered among the best in the world.
In my opinion it is not necessarily a detriment to good beer. Same thing with malt extract, from which you can actually make some damn good beer. But it won't give you the same flexibility as all-grain would.
The reason the big commercial breweries use them is because they strive for consistency -- and hop extract give them just that. It is very predictable. That said they do also put a lot of effort into making beer cost-efficiently. On a larger scale the little things have a big influence on cost. Note that the reason they aren't using malt extract is that it is much more expensive than all-grain, which lets them squeeze the last drop of malt sugars out themselves.
This shouldn't stop them from making good beer though, as there is no defense against making bad beer.
Monday, February 12, 2007
Probably the best aroma in the world

..or perhaps not.
I've had a 60 ml glass of liquid aroma extract that is intended to be used by commercial breweries for a while. Now this is a lot of hop extract. Well, the label does not actually say hops, whatever. The glass has been left alone in the fridge as I have had no idea what to do with it. I haven't been particularly tempted to actually try it out in one of my 25 liter batches. I do quite a bit of experimentation, but this wouldn't count as one that would be worth it.
Today I found a 500 ml can of lager lying around and found that I should give the extract a try.

Well, how much extract to use? I had no idea. I suspect that these glasses are meant to be used in pretty big batches. In retrospect I wouldn't be surprised that we're taking about something like 25.000 liters of, ahem, definitely not the best beer in the world, Danish lager. After all, there isn't that much hop aroma in a bland commercial lager.

The smallest measuring spoon I have is 1 ml and I decided to just go ahead and add that to half of the contents of the can. I did that so that I could dilute the mixture with the remaining beer, if neccessary.
The extract itself isn't particularly viscous like syrup, but is instead more like cough medicine. It smells really strong. There is an intense floral and grassy aroma that melds into an almost unbearable pungent syrup.
I stirred the extract in the 1 ml spoon into the beer. It didn't quite mix with the beer, but instead formed drops of heavier yellow clumps. If you look closely that the image above you can see these yellow drops forming.
The one sip I had from the glass almost made me puke. The experience was just too intense. It was just like drinking gasoline. I decided not to waste the remaining beer.
Well, that's enough experimentation on my part. If anybody would like to try it out in a 25 liter batch please let me know. There's still 59 ml left.
Thursday, February 08, 2007
#40, #41 and #42: Kegged and bottled
This time it came to a fairly short fermentation for all three brews. Both the Bohemian Pilsener and the Belgian Strong Dark fermented quickly and below their FG targets. The India Pale Ale did also ferment quickly, but didn't quite reach the target which I believe is because of a higher than intended mash temperature, complex malts and a cold fermentation.
The Belgian Strong Dark ended up with a whopping 11.3% abv. Wow. The FG was 1.011, which was 5 points below where I thought it would end up. I blame the simple sugars. Spot on with the Rochefort 10, a beer which the sample I had brought images of. I also found the beer to be a bit lighter in colour than I had expected. The same thing happened with the Belgian Amber I did a while back. The liquid candi sugar is clearly not as dark as stated on the bottle. Because this is a really strong beer it should keep for a while, so I bottled all of it. Having a 11.3% beer on tap is not optimal, it would have been fun, but not good for the keg rotation.
I mentioned earlier that there was a sulphurous smell from the Pilsener fermentation. That did go away after a couple of days. In all the fermentation was really quiet, almost no krausen on top and no bubbles through the airlock (because of a leak in the lid I guess). The FG was 1.013, exactly as estimated.
The final gravity for the India Pale Ale was 1.019, which is 3 points above the estimate. There is quite a bit of specialty malts in this beer, and some of them are not entirely fermentable. The aroma is also surprisingly nutty, likely because of the amber malts. The small uncarbonated sample I tried had a slightly sharp bitterness, but was overall not that bitter. And as expected, there was quite a bit of hop aroma. Life is good.
The Belgian Strong Dark ended up with a whopping 11.3% abv. Wow. The FG was 1.011, which was 5 points below where I thought it would end up. I blame the simple sugars. Spot on with the Rochefort 10, a beer which the sample I had brought images of. I also found the beer to be a bit lighter in colour than I had expected. The same thing happened with the Belgian Amber I did a while back. The liquid candi sugar is clearly not as dark as stated on the bottle. Because this is a really strong beer it should keep for a while, so I bottled all of it. Having a 11.3% beer on tap is not optimal, it would have been fun, but not good for the keg rotation.
I mentioned earlier that there was a sulphurous smell from the Pilsener fermentation. That did go away after a couple of days. In all the fermentation was really quiet, almost no krausen on top and no bubbles through the airlock (because of a leak in the lid I guess). The FG was 1.013, exactly as estimated.
The final gravity for the India Pale Ale was 1.019, which is 3 points above the estimate. There is quite a bit of specialty malts in this beer, and some of them are not entirely fermentable. The aroma is also surprisingly nutty, likely because of the amber malts. The small uncarbonated sample I tried had a slightly sharp bitterness, but was overall not that bitter. And as expected, there was quite a bit of hop aroma. Life is good.
Friday, January 26, 2007
A brew day
In order to give you a rough overview of what my brew day looks like I've created the schedule below that shows the order and the timing of the various steps that I go through when brewing a batch of beer.
00:00 weigh grist, heat mash water
00:15 crush grist (using barley crusher)
00:30 mash-in (add 80C water)
01:30 mash-out (add 100C water)
01:40 first batch sparge
01:55 add sparge water
02:05 second batch sparge
02:10 90 min: big kettle reaches boil, weigh hops
02:20 80 min: small kettle reaches boil (a little later as this contains the second sparge)
02:40 60 min: add bittering hops
03:25 15 min: add flavour hops, insert immersion chiller
03:30 10 min: add irish moss or whirlfloc, add yeast nutrient
03:40 0 min: add aroma hops, flame-out
03:45 start chilling (submerge small kettle in cold water. run tap water through chiller)
04:25 siphon wort into fermenter (splashing)
04:45 add yeast, oxygenate wort
05:30 done cleaning
A brewing session usually takes somewhere between 5 and 6 hours depending on how good I am at multi-tasking. I also get a couple of longer breaks, the first one throughout the 1 hour mash and the second between the addition of bittering hops and flavouring hops. I usually spend that time reviewing the recipe and the process itself.
As you can see above I mash for 60 minutes. The mash itself lasts 60 minutes, then boiling water is added to raise the mash to about 76C. I'm not always successful hitting that temperature, but that really depends a little on how much water there is in the mashtun already. Then I wait 10 minutes so that the mash can settle, making it less turbid. I then open the ball value and vorlauf about 1 liter, which I then pour on top of the mash through some aluminum foil.
I boil for a total of 90 minutes, but add the bittering hops 30 minutes into the boil. I do this to get a better hot break. The proteins coagulate more easily when there are no hops in there. This should in theory give clearer beer. The difference in bitterness extraction is minimal, so this a pretty good trade-off.
My chilling procedure is perhaps not the best one. I use a home-made immersion chiller which is decent. Since I have to boil in two pots I can only insert the chiller into the biggest one (20 liters). This means that I have to chill the small pot (12 liters) in the sink with cold water. This is not the most efficient way to chill wort, but it works. Chilling the wort as quickly possible is a good thing. The longer the aroma hops are steeped in the wort the more likely it is to extract vegetal flavours. Once I get my new kettle going I'll be able to chill all the wort in one go. I think the immersion chiller should work. If not I'll look into getting a plate chiller or a counter-flow chiller.
When transferring the chilled wort into the fermentation vessel I try to splash the wort as much as possible to get some in oxygen into it. The yeast needs lots of oxygen during the reproduction phase. Once everything is transferred I close the lid and shake it vigorously for a minute or two. Combined with lots of yeast this seems to work just fine.
00:00 weigh grist, heat mash water
00:15 crush grist (using barley crusher)
00:30 mash-in (add 80C water)
01:30 mash-out (add 100C water)
01:40 first batch sparge
01:55 add sparge water
02:05 second batch sparge
02:10 90 min: big kettle reaches boil, weigh hops
02:20 80 min: small kettle reaches boil (a little later as this contains the second sparge)
02:40 60 min: add bittering hops
03:25 15 min: add flavour hops, insert immersion chiller
03:30 10 min: add irish moss or whirlfloc, add yeast nutrient
03:40 0 min: add aroma hops, flame-out
03:45 start chilling (submerge small kettle in cold water. run tap water through chiller)
04:25 siphon wort into fermenter (splashing)
04:45 add yeast, oxygenate wort
05:30 done cleaning
A brewing session usually takes somewhere between 5 and 6 hours depending on how good I am at multi-tasking. I also get a couple of longer breaks, the first one throughout the 1 hour mash and the second between the addition of bittering hops and flavouring hops. I usually spend that time reviewing the recipe and the process itself.
As you can see above I mash for 60 minutes. The mash itself lasts 60 minutes, then boiling water is added to raise the mash to about 76C. I'm not always successful hitting that temperature, but that really depends a little on how much water there is in the mashtun already. Then I wait 10 minutes so that the mash can settle, making it less turbid. I then open the ball value and vorlauf about 1 liter, which I then pour on top of the mash through some aluminum foil.
I boil for a total of 90 minutes, but add the bittering hops 30 minutes into the boil. I do this to get a better hot break. The proteins coagulate more easily when there are no hops in there. This should in theory give clearer beer. The difference in bitterness extraction is minimal, so this a pretty good trade-off.
My chilling procedure is perhaps not the best one. I use a home-made immersion chiller which is decent. Since I have to boil in two pots I can only insert the chiller into the biggest one (20 liters). This means that I have to chill the small pot (12 liters) in the sink with cold water. This is not the most efficient way to chill wort, but it works. Chilling the wort as quickly possible is a good thing. The longer the aroma hops are steeped in the wort the more likely it is to extract vegetal flavours. Once I get my new kettle going I'll be able to chill all the wort in one go. I think the immersion chiller should work. If not I'll look into getting a plate chiller or a counter-flow chiller.
When transferring the chilled wort into the fermentation vessel I try to splash the wort as much as possible to get some in oxygen into it. The yeast needs lots of oxygen during the reproduction phase. Once everything is transferred I close the lid and shake it vigorously for a minute or two. Combined with lots of yeast this seems to work just fine.
Subscribe to:
Posts (Atom)